Reverse Components Handlebars

Bar width has to match shoulder width and armspan. That´s why we created the Youngstar handlebar, to have a handlebar that matches the size and position to give younger riders more control, which equals more fun!

The Youngstar handlebar is a lightweight 6061 T6 aluminium handlebar, 660 mm wide with a 22 mm rise. This fits well for riders approx.140 -155 cm in height. The reduced width and high rise puts them in an optimum position to lift the wheel off the ground, make changes in position and to actively control the bike. We increased the backsweep slightly to bring the bars in towards the riders hands, to increase control further.

The result is a lightweight, high spec handlebar, with custom ergonomics that allow your child to shred the trail with more confidence and control.

Size Recommendation for Kids' Handlebars:
Height - 115-130 cm -> 560 mm handlebars
Height - 130-145 cm -> 620 mm handlebars
Height - 140 -155 cm -> 660 mm handlebars

*The values shown above are a guide only and subject to personal preference.

Features
Width : 560mm or 660mm
Clamp Diameter : 31.8mm
Rise : 22mm
Upsweep : 560mm 5 degrees, 660mm 4 degrees
Backsweep : 560mm and 660mm 9 degrees
Weight : 560mm 248g  -  660mm 279g (+/- 5% weight tolerance)
Material: Aluminium 6061

Extras
- Child-friendly geometry
- Reverse stem alignment lines: for orientation when mounting on the stem

We initially designed and built the Deviant as a trial handlebar.
The outcome was the Deviant handlebar which is primarily intended for trials. However, we soon noticed that this handlebar is very popular among our customers as a high-rise bar for any use. Due to its rise of 76 mm and its pleasingly backsweep of 9°, this handlebar allows an extremely upright position on the bike, for leisure and daily commuting rides!

• Features
  - Width: 730 mm
  - Ø: 31.8 mm
  - Rise: 76 mm
  - Backsweep: 9°
  - Upsweep: 5°
  - Weight: 358 g (+/- 5% weight tolerance)
  - Material: Aluminium 7075-T6

• Extras
  - Reverse stem alignment lines: for orientation when mounting on the stem
  - Cutting lines: for orientation when shortening the handlebar

  • 
    

Our Base handlebar is one of the most popular handlebars in the Reverse riding community. With a width of 790 mm, it is built as all-purpose to be used in Downhill as well as for All mountain and Enduro riding.

A wide handlebar is still the best choice to put as much pressure on the front wheel as possible and supports the driver in the best possible way. Built from double butted 7075 aluminium, this handlebar always gives you confidence and safety, even for toughest abuse!

The handlebar shown here with a clamping size of 31.8 mm, which is still the most used diameter on the market. The two rise versions of the Base 790 make it easy to fit the individual needs of riders and adapt the cockpit to personal preferences. Our Base handlebars are available in different colours and can be combined perfectly to create the perfect custom build.

Features

• - Width: 790 mm
  - Clamp Diameter : 31.8 mm or 35mm
  - Rise: 18mm or 35mm
  - Backsweep: 7°
  - Upsweep: 5°
  - Weight: 31.8/18mm 299g  -  31.8/35mm 303g  -  35/18mm 346g  -   35/35mm 327g (+/- 5% weight tolerance)
  - Maximum permissible bike + rider weight: 130 kg
  - Material: Aluminium 7075 (double butted)

Our Base handlebar is one of the most popular handlebars in the community. With a width of 790 mm, it can be used in Downhill as well as for All mountain and Enduro riding.

A wide handlebar is still the best choice to put as much pressure on the front wheel as possible and supports the driver in the best possible way. Built from double butted 7075 aluminium, this handlebar always gives you confidence and safety, even for toughest abuse!

Features

• - Width: 760 mm
  - Clamp Diameter : 25.4 mm
  - Rise: 18 mm or 38mm
  - Backsweep: 7°
  - Upsweep: 5°
  - Weight: 299 g (+/- 5% weight tolerance)
  - Material: Aluminium 7075 (double butted)

  Extras

  • - Reverse stem alignment lines: for orientation when mounting on the stem

The lead is a true all-rounder! With its comfortable width, this handlebar fits for all disciplines, from cross country, trail to Enduro and dirt jump.

Double butted aluminium, a wide range of colours and a comfortable combination of rise, back and upsweep are the key features of this handlebar.

The 25 mm Rise, preferred by many riders, can usually only be found on our Seismic Series high end carbon handlebars. After many requests for an aluminium bar with this rise, we decided to go for this ride for the Lead bar.

Our Lead cuts the gap between our 18 mm and 35 mm Rise aluminium handlebars, providing an alternative for those who prefer a 25 mm rise.

Ergonomics / Performance / Reliability / Colour Selection!

Features

• - Width: 770 mm
  - Ø: 31.8 mm
  - Rise: 25 mm
  - Upsweep: 4°
  - Backsweep: 9°
  - Weight: 295 g (+/- 5% weight tolerance)
  - Maximum permissible bike + rider weight: 130 kg
  - Material: Aluminium 7075 (double butted)

  Extras

  - E-Safety Level: Category 4 (High)
  - EFBE E-MTB Tri Test (EPAC MTB-AM) tested
  - Cutting lines: for orientation when shortening the handlebar
  - Alignment lines: as a guide when mounting brake lever and trigger
  - Reverse stem alignment lines: for orientation when mounting on the stem

Nico trusts this handlebar!
whether at the Rampage, in the Bikepark at the Darkfest or on the Enduro Bike.....

With its increased wall thickness it can withstand even the toughest abuse!
We have built this handlebar to his specifications and preferences, that’s why this handlebar deserves his personal logo! The Nico Vink Signature Handlebar is designed for those who value strength and reliability over light weight.
We offer the Vink Signature handlebar in different version to fit everyone’s needs. The version with 48 mm is exactly the handlebar which Nico uses on his bikes

“There is no other part on my Bike I have to rely on more than the handlebar. And I have absolute trust in this one! Thanks to the different Rise options it perfectly fits on all of my different Bikes " Niko Vink.

Features
Width : 810mm
Clamp Diameter : 31.8mm or 35mm
Rise : 18mm, 35mm, 48mm
Upsweep : 5 degrees
Backsweep : 31.8/18mm and 31.8/35mm 7 degrees
31.8/48mm, 35/35mm and 35/48mm 9 degrees
Maximum permissible bike + rider weight: 130 kg
Material: Aluminium 7075 (double butted)

Extras
- E-Safety Level: Category 5 (Maximum)
- EFBE E-MTB Tri Test (EPAC MTB-GR) tested
- Extra reinforced 7075 Aluminium for highest resistance to stress
- Cutting lines: for orientation when shortening the handlebar
- Reverse stem alignment lines: for orientation when mounting on the stem

The ELEMENT handlebars of the E-SERIES are characterized by their exceptional strength and stiffness. With our new ELEMENT BUTTING technology we are able to build our handlebars more stable than ever before with an excellent strength to weight ratio.

Based on real-time data we developed a revolutionary test procedure together with the EFBE Prüftechnik GmbH in Germany, where our Element handlebars are tested under the toughest conditions for safe use on e-bikes.
So if you do not want to compromise on safety or design in your e-bike components, then our ELEMENT handlebar is the right choice!

Features

Width : 770mm
Clamp Diameter : 31.8mm
Rise : 25mm or 40mm
Backsweep : 12 degrees
Upsweep : 5 degrees
Weight :  31.8/25mm 312g  -   31.8/40mm 312g  (+/- 5% weight tolerance)
Maximum permissible bike + rider weight: 130 kg
Material: Element aluminium

Extras

- E-Safety Level: Category 4 (High)
- EFBE E-MTB Tri Test (EPAC MTB-AM) tested
- Element butted aluminium
- Cutting lines: for orientation when shortening the handlebar
- Alignment lines: for orientation when mounting on the stem

The ELEMENT handlebars of the E-SERIES are characterized by their exceptional strength and stiffness. With our new ELEMENT BUTTING technology we are able to build our handlebars more stable than ever before with an excellent strength to weight ratio.

Based on real-time data we developed a revolutionary test procedure together with the EFBE Prüftechnik GmbH in Germany, where our Element handlebars are tested under the toughest conditions for safe use on e-bikes.
So if you do not want to compromise on safety or design in your e-bike components, then our ELEMENT handlebar is the right choice!

Features

Width : 740mm
Clamp Diameter : 31.8mm
Rise : 25mm or 40mm
Backsweep : 12 degrees
Upsweep : 5 degrees
Weight :  31.8/25mm 305g  -   31.8/40mm   (+/- 5% weight tolerance)
Maximum permissible bike + rider weight: 130 kg
Material: Element aluminium

Extras

- E-Safety Level: Category 4 (High)
- EFBE E-MTB Tri Test (EPAC MTB-AM) tested
- Element butted aluminium
- Cutting lines: for orientation when shortening the handlebar
- Alignment lines: for orientation when mounting on the stem

The ELEMENT handlebars of the E-SERIES are characterized by their exceptional strength and stiffness. With our new ELEMENT BUTTING technology we are able to build our handlebars more stable than ever before with an excellent strength to weight ratio.

Based on real-time data we developed a revolutionary test procedure together with the EFBE Prüftechnik GmbH in Germany, where our Element handlebars are tested under the toughest conditions for safe use on e-bikes.
So if you do not want to compromise on safety or design in your e-bike components, then our ELEMENT handlebar is the right choice!

Features

Width : 800mm
Clamp Diameter : 31.8mm or 35mm
Rise : 25mm or 40mm
Backsweep : 7 degrees
Upsweep : 5 degrees
Weight :  35/25mm 362g  -  31.8/40mm 334g  -  31.8/25mm  332g (+/- 5% weight tolerance)
Maximum permissible bike + rider weight: 130 kg
Material: Element aluminium

Extras

- E-Safety Level: Category 4 (High)
- EFBE E-MTB Tri Test (EPAC MTB-AM) tested
- Element butted aluminium
- Cutting lines: for orientation when shortening the handlebar
- Alignment lines: for orientation when mounting on the stem

he ELEMENT handlebars of the E-SERIES are characterized by their exceptional strength and stiffness. With our new ELEMENT BUTTING technology we are able to build our handlebars more stable than ever before with an excellent strength to weight ratio.

Based on real-time data we developed a revolutionary test procedure together with the EFBE Prüftechnik GmbH in Germany, where our Element handlebars are tested under the toughest conditions for safe use on e-bikes.
So if you do not want to compromise on safety or design in your e-bike components, then our ELEMENT handlebar is the right choice!

Features

Width : 770mm
Clamp diameter : 25.4mm, 31.8mm, 35mm
Rise : 25mm or 40mm
Backsweep : 9 Degrees
Upsweep : 4 Degrees
Weight : 35/25mm 365g  -   35/40mm 360g  -   25.4/25mm 340g  -   31.8/25mm 310g  -   31.8/40mm 312g (+/- 5% weight tolerance)
Maximum permissible bike + rider weight: 130 kg
Material: Element aluminium

Extras

- E-Safety Level: Category 4 (High)
- EFBE E-MTB Tri Test (EPAC MTB-AM) tested
- Element butted aluminium
- Cutting lines: for orientation when shortening the handlebar
- Alignment lines: for orientation when mounting on the stem

We have incorporated our knowledge and experience, which we have collected in recent years in Downhill and Enduro racing, into the production of the new XC series. Our goal was to produce a handlebar series that which meets the evolving demands of aggressive cross country racing. The outcome is our TRACER XC handlebar range.

Depending on the Rise weighs, this competitive 760 mm wide handlebar weighs between 126 and 131 grams. The low weight does not affect the stability in any way! We have set the same standards as our downhill handlebars.
Strong, light and reliable!

Features
- Width: 760 mm
- Ø: 31.8 mm
- Rise: 0 mm
- Backsweep: 9°
- Upsweep: 0°
- Weight: 126 g (+/- 5% weight tolerance)
- Material: Carbon

• Extras
  - Cutting lines: for orientation when shortening the handlebar
  - Alignment lines: as a guide when mounting brake and trigger terminals
  - Reverse stem alignment lines: for orientation when mounting on the stem
  - Reverse “Sandpaper” stem fixation: roughened surface in the stem clamping area to increase the clamping effect
  - Reverse “Sandpaper”: roughened surface in the grip area to increase the clamping effect

Less vibrations equals more energy to charge!
The Seismic Carbon is our flagship handlebar, the goal for the bar was to make the strongest carbon bar possible, while focusing on the reduction of vibrations which occur on long runs in rough terrain which cause lower arm fatigue, leading to less arm-pump and the ability to ride more and for longer!
There have been and are many approaches to achieve this, even filling the handlebars with foam. But to solve the problem and efficiently reduce vibrations, you have to start with the material first. And that's what we did.  

In close cooperation with our engineers and our test laboratory EFBE in Germany, we looked for a solution to produce a bar with exceptional strength and longevity with compliance that improved the ride quality. The result was a unique processing technology of carbon laminates which makes it possible to produce a handlebar which is a lightweight and strong under the harshest conditions. By optimising the layup to produce the desired amount of compliance, we produced a carbon handlebar that actively reduces arm-pump by dulling impacts and reducing vibrations rather than producing a harsh ride. A bar that gives you confidence to launch into rocks and roots sections, without the fear of a shock through the hands when you land.

The Seismic handlebar is tested to the highest level, it passed the strongest possible handlebar test standard that exists – the EFBE EPAC MTB-GR 2021– suitable for the toughest E-Bike and DH use, thanks to its Safety-Level 5 approval.
Whether you’re mastering stages on the Enduro World Series, hitting DH runs and Bikepark laps or simply want the most durable and best feeling carbon bar possible for your rides, the Seismic is carbon done right.

Available in both Ø 31.8mm and Ø 35mm diameters, with a 25mm rise, in a full 810mm length with cutting lines.

Features

• - Width: 810 mm
  - Ø 31.8 mm (and 35.0 mm)
  - Rise: 25 mm
  - Upsweep: 5°
  - Backsweep: 7°
  - Weight: 200 g (+/- 5% weight tolerance) (197g Ø 35.0 mm)
  - Maximum permissible bike + rider weight: 130 kg
  - Material: Carbon

  Extras

  - Cutting lines: for orientation when cutting down the handlebar (minimum width 720mm)
  - Alignment lines: for orientation when mounting on the stem
  - Reverse “Sandpaper” stem fixation: roughened surface in the stem clamping area to increase the clamping effect
  - Reverse “Sandpaper” grip & brake fixation: roughened surface in the grip area to increase the clamping effect and to eliminate twisting of grips, brake and trigger clamps
  - E-Safety Level: Category 5 (Maximum)
  - EFBE E-MTB Tri Test (EPAC MTB-GR) tested